$ 442.00 4 $ 515.00
Boiler Water Sample Cooler is a safe method of withdrawing water from boilers, steam lines or tanks containing chemicals and for cooling the withdrawn liquid for subsequent chemical analysis.
This Boiler Water Sample Cooler is easy to install.
The inner coil uses 316 stainless steel and is one-piece
construction.
Removable coil samples coolers are also available.
Made in the USA.
• Rugged all-welded construction
• Internal baffles to insure maximum heat transfer
• Heat exchange area - one sq. ft.
• Design ratings of sample tubing - 3500psi at 750°F
• Design ratings of shell - 300psi at 250°F
• All 316 Stainless Steel construction
• Approach temperature is added to the cooling water inlet temperature to obtain
sample outlet temperature.
• Numbers given above vary with steam quality and are approximate.
• Increasing cooling water flow will reduce cooling water outlet temperature.
• Steam samples are to be throttled on the discharge of the cooler.
• For superheated samples over 750°F, leaving a portion of the tubing run to the cooler
from the source uninsulated typically will reduce the temperature sufficiently to the max
750°F. See the graph showing a general guideline for minimum exposed pipe/tube needed.
1. Open the cooling water inlet valve first.
2. Open the sample inlet valve and gradually open the sample outlet valve
to regulate the flow to achieve a cooled sample.
3. Allow the sample to run for a while before collection.
4. When enough liquid has been collected close the sample inlet first, and
then the cooling water inlet valve.
Superheated Steam Sampling
The chart referenced can be used as a guide on how to dissipate
$ 240.00 11
Get an instant 25% discounts by adding to your cart!
Ideal replacement for a solenoid valve that fails frequently, specially in cooling blowdown applications.
Motorized water control valve with electronic return to close when power is removed. This is not a spring loaded actuator. With a nickel plated brass or SS316 body and 1 ", 3/4" or 1/2" FNPT thread, this valve is extremely resistant to hard water or water with high TDS content.
Watch a video! Check it out here
The actuator in this water control valve can handle 95 to 250 VAC and comes with a manual override, for maintenance and operation in case of power failure. With a IP67 enclosure, this is a heavy duty valve that can withstand water splashing and dust.
Need a cooling controller? Check the 140, 1575e or NexSys
Need a solenoid pump? Check out the AML 200, AKL 603, AKL 800 or AKL 803
Need water analysis products? Check them out here
These valves have a 12 months warranty on manufacturing defects! also:
We offer a 30-day money back guarantee on all products that have been purchased from us directly. All items must be returned as new in their original packaging, including all accessories and cables. Missing items will be charged based on suggested retail prices. All returns must be accompanied by a valid return authorization number (RMA) issued by us. If an RMA is not obtained prior to shipping, the returned product will be refused and returned to sender. Shipping cost is not refundable and returns must be shipped prepaid by the customer. To set up a return for refund please email sales@yamathosupply.com . Please be sure to include your order # and reason for returning in your email.
How much is costing you a failing solenoid valve? Solenoid valves are the most used type of electrically actuated valves for water applications. Unfortunately they use a small orifice to control the water flow. This presents two limitations; it can easily be plugged by solids in the water and, limits the water flow, creating big pressure drops. Our motorized ball valves replaces both electrically, and mechanically, any solenoid valve, without the problems mentioned before.
Technical Parameters:
Series |
Max Torque |
Operating Time |
Working Voltage |
Max Power |
Enclosure |
Max Pressure |
Max Temp |
Ambient Temp |
Humidity |
YS20S |
2N.M |
5-7S |
110V, 220V |
3W |
IP67 |
1.6 Mpa 230 psi |
-20~+100°C -4~+220°F |
-20 ~ +45°C -4 ~+113°F |
<95% |
4W |
|||||||||
5W |
$ 240.00 3
Instant Discounts once added to cart!
We ship same day to the continental US if order placed before 3pm EST.
Motorized ball water control valve valve with electronic return to close when power is removed and, electric indication open/close. This is not a spring loaded actuator. With a nickel plated brass or SS316 body and 1 ", 3/4" or 1/2" FNPT thread, 1" PVC Socket ANSI, this valve is extremely resistant to hard water or water with high TDS content. Ideal replacement for a solenoid valve that fails frequently.
This actuator can handle 24 VDC and comes with a manual override for manual operation. With a IP67 enclosure, this is a heavy duty valve that can withstand water splashing and dust.
For more details, please, click on the PDF icon.
Need a cooling controller? Check the 140, 1575e or NexSys
Need a solenoid pump? Check out the AML 200, AKL 603, AKL 800 or AKL 803
Need water analysis products? Check them out here
$ 738.00 2
The Compact ClO2+ (Chlorine test kit) meter provides field analysis of chlorine and chlorine dioxide test kit using the DPD method.
The original Palin system was designed for monitoring of all forms of chlorine. Dr Palin extended the method to measure alternative disinfectants such as chlorine dioxide – a powerful and increasingly popular biocide. The Compact ClO2+ meter delivers the following features:
Available in a choice of hard or soft case kits, the Compact ClO2+ meter is simplicity itself operating with four intuitive keys. Accessories include our unique Neutral Density Filter (NDF) check standards for validation in the field.
Watch this video to see how it works! Click HERE
Instrument Type |
Dual wavelength, direct-reading colorimeter |
Optics |
Palintest dual LED light source optical system with narrow band wavelength filters and photodetectors |
Wavelengths |
530 nm |
Wavelength Tolerance |
± 2nm |
Filter Bandwidth |
10nm |
LCD Display |
128 x 64 pixel screen |
Instrument Operating Temperature Range |
0 to 50°C |
Test Cells |
25 mm diameter tubes |
Blank/Zero setting |
Held in memory or reset for each reading |
Power Supply |
2 x 1.5V ‘AA’ batteries. Auto switch-off setting. |
Size |
150 x 70 x 45 mm |
Weight |
185g (including batteries) |
REAGENTS
TEST |
RANGE (Cl2 - mg/l) |
RANGE (ClO2- mg/l) |
REAGENT PACKS(50 TESTS) |
REAGENT PACKS(250 TESTS) |
DPD No 1 Tablets |
0.01 - 5.0 |
0.02 - 10 |
||
DPD No 3 Tablets |
0.01 - 5.0 |
- |
||
DPD Glycine Tablets |
- |
- |
|
*Please contact us for pricing on reagents
Chlorometer, Chlorometer Instructions, 4 Crushing Rods, Test Tube Brush, 2 x Photometer Tubes.
Reagents:
Chlorine (DPD 1), Chlorine (DPD 3)
2 Cartons (100 reagents per carton)